Baldwin Serial Number

22-05-2021 admin

Vehicle Identification Number (VIN) IMPORTED VEHICLE IDENTIFICATION NUMBER (VIN) (Cont’d.) * See VIN Decoding Information on 9th Character (Check Digit). ENGINE CODE (Sixth Character) PEUGEOT 1981-91 VF3BA516*FS368001 ENGINE CODE (Fifth Character) PORSCHE 2006-on WP0AC2A7XAL090244 ENGINE CODE (Fourth Character) NISSAN (EXCEPT QUEST) 1995-on. To locate the serial number on a vertical piano, open the top and look inside. Almost all of them include the serial number on the plate in a small 'window' near the tuning pins. The number will usually be a 4 to 7 digit number, but may include a letter or two.

Baldwin Serial Number Location
Acrosonic Piano Serial Number Location

Baldwin 60000

Type and origin
Power type	Steam
Builder	Baldwin Locomotive Works
Serial number	60000
Model	16-3-48/48-1/4-F
Build date	1926

Specifications
Configuration:
• Whyte	4-10-2
• UIC	2′E1′ hv3
Gauge	4 ft 8¹⁄₂ in (1,435 mm) standard gauge
Leading dia.	33 in (838 mm)
Driver dia.	63.5 in (1,613 mm)
Trailing dia.	45.5 in (1,156 mm)
Adhesive weight	338,400 lb (153,500 kg; 153.5 t)
Loco weight	457,500 lb (207,500 kg; 207.5 t)
Total weight	700,900 lb (317,900 kg; 317.9 t)
Fuel type	Coal (Briefly converted to oil)
Fuel capacity	32,000 lb (15,000 kg; 15 t)
Water cap	12,000 US gallons (45,000 l; 10,000 imp gal)
Firebox: • Firegrate area	82.5 sq ft (7.66 m²)
Boiler pressure	350 psi (2.41 MPa)
Heating surface: • Tubes and flues	5,192 sq ft (482.4 m²)
• Firebox	745 sq ft (69.2 m²)
Superheater:
• Heating area	1,357 sq ft (126.1 m²)
Cylinders	Center: 1 HP Outside: 2 LP
High-pressure cylinder	27 in × 32 in (686 mm × 813 mm)
Low-pressure cylinder	27 in × 32 in (686 mm × 813 mm)
Valve type	14 in (356 mm) piston valves

Performance figures
Maximum speed	70 mph (110 km/h)
Power output	4,515 hp (3.37 MW)
Tractive effort	82,500 lbf (367.0 kN)

Career
Operators	Baldwin Locomotive Works
Nicknames	Baldwin Boomer
Retired	Stored: 1928, Sold: 1933
Current owner	Franklin Institute Science Museum
Disposition	Display - moves back and forth 15 feet (4.6 m) on a short track powered by hydraulics

Baldwin 60000 is an experimental steam locomotive built by the Baldwin Locomotive Works in Eddystone, Pennsylvania, in 1926, during the height of the railroading industry. It received its number for being the 60,000th locomotive built by Baldwin.^[1]

It was designed to be the best locomotive that Baldwin ever made. It boasts three cylinders, weighs about 350 short tons (318 t; 313 long tons), including tender, and can pull a load of up to 7,000 short tons (6,400 t; 6,200 long tons). Its top speed is 70 mph (110 km/h).^{[citation needed]}

60000 was very innovative, carrying unusual technology, including a water-tube firebox. This was intended to improve efficiency but the tubes were prone to burst inside the firebox. It is also a compound, expanding the steam once in the inside cylinder and then again in the two outside cylinders. Although compounding increases efficiency, it was an extra complication that the US railroads had mostly rejected by the middle twenties.^[2] The weight and length of the engine were too much for all but the heaviest and straightest tracks.

This locomotive was experimental and was meant to be the model for future development. However, its demonstration runs never persuaded railroads to purchase more and in 1933, it was purchased by the Franklin Institute Science Museum for $1^[3] and remains there today.

Testing[edit]

After a series brief test runs following construction, the 60000 was sent to the Pennsylvania Railroad's Altoona Test Plant in Altoona, Pennsylvania. Placed on rollers without its tender, it was tested on the traction dynamometer to measure its performance, which included maximum drawbar horsepower.^[4] Following tests at the Altoona Test Plant, the Pennsylvania Railroad placed the engine in freight service between Enola Yard near Harrisburg and Morrisville Yard via the Trenton Cutoff. During testing on the PRR, 60000 pulled a maximum of 7,700 tons.^[5]

Following testing on the PRR, the 60000 was sent for additional testing on the Baltimore and Ohio Railroad. Between November and December 1926, the 60000 was tested on the Cumberland Division between Brunswick and Keyser, Maryland, the Connellsville Division between Cumberland, Maryland, and Connellsville, Pennsylvania, and the Pittsburgh Division, which included the Sand Patch and Seventeen-Mile grades.^[6]

In February 1927, the 60000 was sent to the Chicago, Burlington and Quincy Railroad's Beardstown Division of Illinois. The 60000 was run in tandem with the CB&Q's own M2-A Class 2-10-2 number 6157, in order to compare coal and water consumption. Overall, the 60000 was superior in its coal and water consumption.^[6]

On 24 February 1927, the 60000 was sent to the Atchison, Topeka and Santa Fe Railroad. Testing was performed on the Pecos division between Clovis and Belen, New Mexico. As with the CB&Q, the AT&SF compared the performance of the 60000 with that of its own power in the form of two 3800-Class 2-10-2s. Once more the 60000 demonstrated superior fuel consumption than the locomotives of the host railroad.^[6]

In the summer and fall of 1927, the 60000 was sent to the Southern Pacific Railroad, which overhauled the locomotive and converted it to an oil burner at its Sacramento Shops. Following its conversion, the 60000 was tested in both freight and passenger service on the Sacramento Division, during which the engine carried a Southern Pacific tender. Following tests on the SP, the 60000 was sent to the Great Northern Railway between Everett, Washington and Minot, North Dakota. Overall, the 60000 did not perform as well on oil as it did on coal^[6]

Converted back to coal, the 60000 was then returned to the Baldwin Locomotive Works and used as a stationary boiler before being sold to the Franklin Institute.

References[edit]